[ Quick Start Guide ]
CONVERGED NETWORK ADAPTER INSTALLATION
z
Quick Start Guide
Installation Instructions
This Quick Start Guide describes how to install and configure your new QLogic Converged Network Adapter (CNA) in
four simple steps:
❑
❑
❑
❑
Step 1. Verify the package contents.
Step 2. Install the CNA hardware.
Step 3. Install the CNA drivers.
Step 4. Install the SANsurfer FC HBA Manager (FCoE support included).
Keep the CNA in the antistatic bag until installation. The CNA contains parts that can be damaged by
electrostatic discharge (ESD). Before handling the CNA, use standard methods to discharge static
electricity. Place the CNA on the bag when examining it. Retain the bag for future use.
CAUTION!
Step 1. Verify the Package Contents:
The QLogic CNA is shipped with the following items
❑
❑
❑
QLogic CNA
Quick Start Guide (this document)
SANsurfer CD
Step 2. Install the CNA Hardware
To install the CNA hardware, you need to open the computer and locate the appropriate bus slot. If necessary, consult
your computer system manual for instructions to remove the computer cover.
Follow these steps to install the CNA hardware:
1.
2.
3.
4.
5.
6.
7.
8.
Power off the computer, then disconnect the power cable.
Remove the computer cover and find an empty PCIe x8 bus slot.
Pull out the slot cover (if any) by removing the screw or releasing the lever.
Grasp the CNA by the top edge and seat it firmly into the appropriate slot.
Refasten the CNA’s retaining bracket using the existing screw or lever.
Close the computer cover.
Plug the appropriate Ethernet cable (either copper or optical) into the CNA.
Plug in the power cable and turn on the computer.
3
CNA
LEVER
SCREW
PCI EXPRESS x8 SLOT RE-
QUIRED FOR QLOGIC CNAs
CNA RETAINING
BRACKET
SLOT COVERS
SYSTEM
CHASSIS
Sample Motherboard and Slots
Step 3. Install the CNA Drivers
To install the FCoE drivers:
1.
2.
3.
4.
From the driver list at the bottom of the page, select FCoE CNAs and QLE8042.
Select the appropriate driver for your operating system.
Follow the included instructions for installing the downloaded driver.
To install the Ethernet drivers:
1.
2.
Center section.
Follow the instructions provided on the Intel website to install the drivers.
4
Step 4. Install the SANsurfer FC HBA Manager (FCoE Support Included)
To install the SANsurfer FC HBA Manager from the CD:
1.
2.
3.
4.
5.
Select your applicable operating system.
Click I Accept on the License Agreement.
Select your specific operating system.
Select the SANsurfer FC HBA Manager install file.
Follow the on-screen directions to complete the installation.
Congratulations! You have successfully installed your QLogic CNA!
❑
To obtain the most current drivers, management tools, user instructions, and documentation, please visit the
❑
The following section contains additional information about the QLogic CNA, including the LED scheme,
warranty, and laser safety information.
CNA LEDs
QLE8042 CNA LED Scheme
Green LED
(Activity, TX/RX)
Green LED (Link)
Activity
Off
On
On
Off
Off
Power on (no link)
Link established, no activity
Flashing
Link established, TX/RX activity
Warranty
Please check the QLogic Web site at http://www.qlogic.com/Support/warranty.aspx for warranty details.
Laser Safety
FDA Notice
This product complies with DHHS Rules 21CFR Chapter I,Subchapter J. This product has been designed and manufactured according to
IEC60825-1 on the safety label of laser product.
Class 1 Laser Product
Appareil laser de classe 1
Produkt der Laser Klasse 1
Luokan 1 Laserlaite
Caution—Class 1 laser radiation when open
Do not view directly with optical instruments
CLASS I LASER
Attention—Radiation laser de classe 1
Ne pas regarder directement avec des instruments optiques
Vorsicht—Laserstrahlung der Klasse 1 bei geöffneter Abdeckung
Direktes Ansehen mit optischen Instrumenten vermeiden
Varoitus—Luokan 1 lasersäteilyä, kun laite on auki
Älä katso suoraan laitteeseen käyttämällä optisia instrumenttej
5
Agency Certification
QLogic CNAs
The following sections contain a summary of EMC/EMI test specifications performed on the QLogic CNAs to comply with radiated emission,
radiated immunity, and product safety standards.
EMI and EMC Requirements
FCC Part 15 compliance: Class A (QLE8042)
FCC compliance information statement: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
ICES-003 compliance: Class A (QLE8042)
❑
For QLE8042 CNAs: This Class A digital apparatus complies with Canadian ICES-003.Cet appareil numériqué de la classe A est
conformé à la norme NMB-003 du Canada.
CE Mark 2004/108/EC EMC Directive compliance:
EN55022:2006/CISPR22:2006 - Class A (QLE8042)
EN55024:1998
Immunity Standards
EN61000-4-2
EN61000-4-3
EN61000-4-4
EN61000-4-5
EN61000-4-6
EN61000-4-8
:
:
:
:
:
:
ESD
RF Electro Magnetic Field
Fast Transient/Burst
Fast Surge Common/ Differential
RF Conducted Susceptibility
Power Frequency Magnetic Filed
EN61000-4-11: Voltage Dips and Interrupt
EN61000-3-2
EN61000-3-3
:
:
Harmonic Current Emission
Voltage Fluctuation and Flicker
VCCI: Class A (QLE8042)
AS/NZS CISPR22: Class A (QLE8042)
CNS 13438: Class A (QLE8042)
❑
For QLE8042 CNAs
This is a Class A product. In a domestic environment, this product may cause radio interference, in which case, the user may
be required to take adequate measures.
MIC: Class A (QLE8042)
For QLE8042 CNAs: Korea MIC Class A Certified
❑
Product Name/Model
Certification holder
Fibre Channel CNA
QLogic Corporation
Manufactured date
Refer to date code listed on product
QLogic Corporation/USA
Manufacturer/Country of origin
A class equipment
(Business purpose info/telecommunications
equipment)
As this equipment has undergone EMC registration for business
purpose, the seller and/or the buyer is asked to beware of this point
and in case a wrongful sale or purchase has been made, it is asked
that a change to household use be made.
6
❑
Korean Language Format— Class A
Product Safety Compliance
UL, cUL product safety: QLE8042
UL60950
CSA C22.2 No.60950
Class 1 Laser Product per DHHS 21CFR (J)
2006/95/EC low voltage directive: QLE8042
TUV:
-EN60950-1:2001+A11
-EN60825-1:1994+A1+A2
-EN60825-2:2004
7
8
9
10
© 2008 QLogic Corporation. QLogic, the QLogic logo, and SANsurfer are registered trademarks or trademarks of QLogic
Corporation. All other brands and product names are trademarks or registered trademarks of their respective owners.
Information supplied by QLogic is believed to be accurate and reliable. QLogic Corporation assumes no responsibility
for any errors in this brochure. QLogic Corporation reserves the right, without notice, to makes changes in product
design or specifications.
FE0154501-00 B
QLogic Corporation
949.389.6000
26650 Aliso Viejo Parkway
Aliso Viejo, CA 92656
FE0154501-00 B
J
|
Q Logic Switch FIRMWARE VERSION 74 User Guide
RCA DVD Player RTD315W User Guide
RCA Garage Door Opener RCRN08GR User Guide
RCA Speaker RP 9990 User Guide
Roberts Radio Microcassette Recorder RC9907 User Guide
Salton Juicer JM1 User Guide
Samsung Blood Pressure Monitor BF 180M User Guide
Samsung Speaker System HW E350 User Guide
Sanyo Car Satellite TV System HT27547 User Guide
Senco Nail Gun GT90CH User Guide