MXa Series
▲
▲
▲
▲
MX 1000a
MX 1500a
MX 2000a
MX 3000a
®
*TD-000026-00*
Rev. B
A
U
D
I
O
I. WARNING NOTICES
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
SPEAKER DAMAGE
CAUTION: To reduce the rish of electric shock, do not remove
the cover. No user-serviceable parts inside. Refer servicing to
qualified service personnel.
The MXa Series amplifiers are among the most powerful
professional amplifiers available and is capable of pro-
ducing much more power than many loudspeakers can
handle. It is the user’s responsibility to use suitable
speakers with the amplifier and to use them in a sensible
way that will not cause damage.
WARNING: To prevent fire or electric shock, do not expose this
equipment to rain or moisture.
QSC will not be responsible for blown speakers. Consult
the speaker manufacturer for power-handling recom-
mendations.
AVIS
EitherchanneloftheMX3000aamplifierhasspecialclip-
limitingprotectioncircuitrythatreducesthesignallevelat
the onset of heavy clipping. This not only allows the
amplifiertooperateatahighaveragepowerlevelwithout
audible distortion occurring, but it also prevents the
speakers’ being destroyed by excessive clipping. How-
ever, if the amplifier is operating normally and your
speakers fail anyway, it is virtually certain that they could
not handle the high power, despite the lack of clipping.
RISQUE DE CHOC
ÉLECTRIQUE
NE PAS OUVRIR
ATTENTION: Pour eviter les risques de choc électrique, ne pas
enlever le courvercle. Aucun entretien de pièces intérieures
par l’usager. Confier l’entretien au personnel qualifié.
AVIS: Pour eviter les risques d’incendie ou d’électrocution,
n’exposez pas cet article à la pluie ou a l’humidité.
Even if you reduce the gain using the amplifier’s front
panel attenuator controls, it is still possible to reach full
output power if the input signal level is high enough.
A single high-power crescendo can blow high-frequency
driversalmostinstantaneously,whilelow-frequencydriv-
ers can usually withstand very high, continuous power
levels for a few seconds before they fail. Reduce power
immediately if you hear any speaker “bottoming out”—
harsh pops or cracking distortion that indicate that the
speaker voice coil or diaphragm is striking the magnet
assembly.
VORSICHT
GEFAHR EINES
ELEKTRISCHEN SCHLAGES.
NICHT ÖFFNEN!
VORSICHT: Um das Risiko eines elektrischen Schlages zu
vermindern, Abdeckung nicht entfernen! Keine Benutzer
Wartungsteile im Innern. Wartung nur durch qualifiertes
Wartungspersonal.
QSC recommends that you use amplifiers of this power
range for more headroom (cleaner sound) rather than for
increased volume.
WARNUNG: Zur vermeidung von Feuer oder elektrischen
Schlägen, das Gerät nicht mit Regen oder Feuchtigkeit in
Berührung bringen!
SPEAKER OUTPUT SHOCK HAZARD
An MXa amplifier is capable of producing hazardous
output voltages. To avoid electrical shock, do not touch
any exposed speaker wiring while the amplifier is operat-
ing.
SAFEGUARDS
Electrical energy can perform many useful functions. This unit has
been engineered and manufactured to assure your personal safety.
Improperusecanresultinpotentialelectricalshockorfirehazards.
Inordernottodefeatthesafeguards,observethefollowinginstruc-
tions for its installation, use and servicing.
RACK MOUNTING PRECAUTIONS
In portable racks, to avoid damage to either the amplifier
mountingearsorthemountingrails, supporttheamplifier
at all four corners. Contact the QSC Customer Service
Department to order rear support brackets.
PRECAUTIONS
L’énergie électrique peut remplir de nombreuses fonctions utiles.
Cet appariel a été conçu et réalisé pour assurer une sécurité
personnelle entiére. Une utilisation impropre peut entraîner des
risques d’électrocution ou d’incendie. Dans le but de ne pas rendre
inutiles les mesures de sécurité, bien observer les instructions
suivantes pour l’installation, l’utilisation et l’entretien de l’appareil.
3
Theamplifiersrequirearackdepthof18inches(45.7cm)
to clear the rear support ears. Allow some additional
clearance for input and output connectors at the rear
panel, which is 16.9 inches (42.9 cm) behind the plane of
the front mounting rails. The built-in cooling fan draws air
in at the rear of the chassis and exhausts it through vents
in the front panel. The flow-through cooling scheme
allows you to rack-mount the amplifiers one atop the
other, with no clearance necessary in between. This
mounting technique also helps support the weight of the
upper amplifiers.
II. OVERALL DESCRIPTION
The MXa Series from QSC comprises four high-effi-
ciency professional power amplifier models, each with
two independent channels. The MX 1000a, MX 1500a,
and MX 2000a, can deliver, respectively, 275, 400, and
475 watts into 8-ohm loads, and 400, 600, and 725 watts
into 4-ohm loads
Either channel of the MX 3000a is capable of delivering
850 watts into 8-ohm loads, 1300 watts into 4-ohm loads,
or more than 1600 watts into 2 ohms.
TheMXaSeriesderivesmuchofitsdesignfromourhigh-
end EX Series amplifiers. They are engineered for stabil-
ity and exceptional reliability, with protection for open or
short circuits and mismatched loads. To protect your
loudspeakers, the outputs mute during turn-on and turn-
off, and also in the event of a DC fault. All protection
circuitry automatically resets to normal when conditions
assure safe operation.
Each channel has its own transformer secondary (MX
1000a and MX 1500a) or power transformer (MX 2000a
and MX 3000a) and bipolar multi-rail power supply. The
power transformers are mounted in the front of the
amplifier chassis, as close to the front mounting rails as
possible; this keeps the unit’s center of gravity forward to
minimize the twisting force on the front mounting ears.
Still, the amplifier should be supported at all four corners,
especially if it is in a portable rack such as in touring or
mobile applications.
The amplifiers feature thermal protection. The MX 3000a
features a variable-speed fan, which responds continu-
ously to the cooling needs to minimize noise and dust
build-up, and a thermal limiter that reduces gain up to 15
dB if the amplifier overheats above 80˚ C. The other
models have a two-speed fan. If an MXa amplifier over-
heats to 85˚ C or higher, a protection circuit mutes the
output.
The MX 1000a and MX 1500a are both two rack spaces
high and weigh 19 kg (42 lb). The MX 2000a and MX
3000a occupy three rack spaces. The MX 2000a weighs
24.5 kg (54 lb), and the MX 3000a weighs 31 kg (69 lb).
GAIN 1
10
GAIN 2
10
ON
12
8
12
8
PROT CLIP
SIG PWR
PWR SIG
CLIP PROT
14
18
24
6
14
18
24
6
4
4
2
2
OFF
0
0
MX 1500a
Professional Stereo Amplifier
- dB
- dB
Figure 1: QSC MX 1500a Front Panel (identical to the MX 1000a)
GAIN 1
10
GAIN 2
ON
10
12
8
12
8
PROT CLIP
SIG PWR
PWR SIG
CLIP PROT
14
18
24
6
14
18
24
6
4
4
2
2
OFF
0
0
MX 2000a
Dual Monaural Amplifier
- dB
- dB
Figure 2: QSC MX 2000a Front Panel (identical to the MX 3000a)
4
MX 1500a INPUTS
III. INPUTS
The amplifier’s input sensitivity is 1.07 volt rms; at this
signal level and any attenuators set for full gain, the
amplifier will produce full rated power—350 watts, 20Hz-
20kHz,0.1%THD—intoan8-ohmload.Theinputimped-
ance is 20 kilohm balanced and 10 kilohm unbalanced,
typical of QSC amplifiers.
An MXa amplifier features balanced inputs, connected
via barrier strip terminals or 1/4” (6.3 mm) tip/ring/sleeve
phone jacks. The tip of the input jack is wired for “nega-
tive’orinvertedpolarity,whiletheringisthenon-inverting
input. Thus, ifthevoltageatthetipispositivewithrespect
to that at the ring, the amplifier channel will produce a
negative voltage at its output.
For use with unbalanced signals, connect the unused
terminal to ground to avoid a reduction in gain caused by
a floating input; use a two-conductor (tip/sleeve) plug, or
connect a jumper between the inverting input terminals
on the barrier strip and their adjacent ground terminal.
MX 2000a INPUTS
The amplifier’s input sensitivity is 1.05 volt rms; at this
signal level and any attenuators set for full gain, the
amplifier will produce full rated power—450 watts, 20Hz-
20kHz,0.1%THD—intoan8-ohmload.Theinputimped-
ance is 20 kilohm balanced and 10 kilohm unbalanced,
typical of QSC amplifiers.
MX 1000a INPUTS
The amplifier’s input sensitivity is 1.1 volt rms; at this
signal level and input attenuators set for full gain, the
amplifier will produce full rated power—250 watts, 20Hz-
20kHz,0.1%THD—intoan8-ohmload.Theinputimped-
ance is 20 kilohm balanced and 10 kilohm unbalanced,
typical of QSC amplifiers.
MX 3000a INPUTS
The amplifier’s input sensitivity is 1 volt rms; at this signal
levelandanyattenuatorssetforfullgain,theamplifierwill
produce full rated power—800 watts, 20Hz-20kHz, 0.1%
THD—into an 8-ohm load. The input impedance is 20
kilohm balanced and 10 kilohm unbalanced, typical of
QSC amplifiers.
An MXa Series amplifier features a Level I Open Input
Architecture slot. See Section 2 for more information
about Open Input Architecture.
–
–
BRIDGED MONO
+
+
WARNING:TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
EQUIPMENT TO RAIN OR MOSTURE.
A
U
D
I
O
CHANNEL 2
CHANNEL 1
AVIS
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
–
–
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
TIP NEG RING POS
SLEEVE GND
TIP NEG RING POS
SLEEVE GND
CLASS 2 WIRING
STEREO 4 OHM MIN/CH.
CH 2 INPUT CH 1
BRIDGED MONO 8 OHM MIN. CLASS 1 WIRING MUST BE USED
BRIDGED MONO OPERATION: PLACE BRIDGING SWITCH ON INPUT PANEL
TO BRIDGED POSITION. CONNECT INPUT SIGNAL TO CH 1 ONLY.
CONNECT SPKR (+) TO CH 1 (+) OUTPUT. CONNECT SPEAKER (–) TO
CH 2 (+) OUTPUT. SET CH 2 GAIN FULLY CLOCKWISE AND REGULATE
LEVEL WITH CH 1 GAIN CONTROL.
STEREO
PARALLEL
BRIDGE
CH 2
CH 1
–
GND
–
+
+
Figure 3: QSC MX 1500a Back Panel (identical to the MX 1000a)
–
–
BRIDGED MONO
WARNING:TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
EQUIPMENT TO RAIN OR MOSTURE.
+
+
CHANNEL 2
CHANNEL 1
–
–
TIP NEG RING POS
SLEEVE GND
TIP NEG RING POS
SLEEVE GND
CH 2 INPUT CH 1
CLASS 2 WIRING
STEREO 4 OHM MIN/CH.
STEREO
BRIDGED MONO 8 OHM MIN. CLASS 1 WIRING MUST BE USED
BRIDGED MONO OPERATION: PLACE BRIDGING SWITCH ON INPUT PANEL
TO BRIDGED POSITION. CONNECT INPUT SIGNAL TO CH 1 ONLY.
CONNECT SPKR (+) TO CH 1 (+) OUTPUT. CONNECT SPEAKER (–) TO
CH 2 (+) OUTPUT. SET CH 2 GAIN FULLY CLOCKWISE AND REGULATE
LEVEL WITH CH 1 GAIN CONTROL.
PARALLEL
BRIDGE
CH 2
CH 1
–
GND
–
+
+
AVIS
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
CAUTION
RISK OF ELECTRIC SHOCK
A
U
D
I
O
DO NOT OPEN
Figure 4: QSC MX 2000a Back Panel (identical to the MX 3000a)
5
IV. OUTPUTS
V. OPERATIONS
When the amplifier is first turned on, the red “PROT” LED
on each channel will light for about three seconds, during
which the output relays will stay open to mute the speak-
ers. After the turn-on muting interval, the “PROT” LEDs
turn off, the green “PWR” LEDs light, and the output
relays close to enable the speaker outputs. Even during
themutinginterval, theyellow“SIG” andred“CLIP” LEDs
operate normally if there is a signal present. If the “CLIP”
LED is on while the amplifier is muted, cut the gain back
immediatelytoavoidafull-powerblastofsoundwhenthe
output relays close. (Whenever it is practical, at turn-on
youshouldhavetheattenuatorsallthewaydowntoavoid
this situation.) If a channel stays muted with “PROT” lit,
or if its “SIG” or “CLIP” indicators light up when the gain
is turned all the way down, it may be defective; see the
troubleshooting segment for more information.
Four “touch-proof” binding posts—one pair per chan-
nel—on the rear panel allow speaker cable connections
to the amplifier outputs. The special design allows con-
nection of large diameter speaker cable while reducing
shock hazard due to the high output power of MXa
amplifiers.The“hot”terminalofeachoutputpairisthered
one; the black one is signal ground.
If you are operating the amplifier in “bridged” mode,
connect the speaker load across the red terminals only;
the red terminal of Channel 1 then is “hot” or “in-phase.”
The red terminal of Channel 2 is not grounded, however,
so use the same precautions in handling and dressing
the wire that you would for the normal “hot” outputs.
CONTROLS AND DISPLAYS
The “SIG” LED indicates signal levels that are -30 dB
The front panel-mounted attenuator controls are labeled
indBofattenuationandarecontinuouslyadjustablefrom
0 dB (full gain) to ∞ (full kill).
(referenced to full output power) or higher.
When the amplifier is shut off, the amplifier should mute
both channels virtually instantaneously, with the “PROT”
indicators lit until the power supplies are discharged.
The LED displays for each channel function as follows:
ON/OFF MUTING
The “PROT” indicator lights
whenever the output is muted. At
turn-on, the amplifier mutes for a
few seconds; at turn-off, it mutes
immediately and remains muted
until the power supplies have
drained.
PWR SIG
CLIP PROT
LED
COLOR
PWR
SIG
Green
Yellow
Red
Main power supply active on this channel.
Shows signal is present
NO SIGNAL
PWR SIG
CLIP
Shows output capability is being
exceeded, with clipping distortion
Only the “PWR” LED is lit. This is
normal.
CLIP PROT
PROT
Red
Shows when the output is muted by
protection circuitry.
Table 1: LED Display Operation
NORMAL SIGNAL
The “PWR” LED is lit, and the
“SIG” LED is lit or flashing. This
is normal.
CLIP PROT
PWR SIG
AC POWER
Any MXa Series amplifier can be wired for 100, 120, or
220–240 VAC, 50 or 60 Hz operation. Unless it is spe-
cially ordered, each amplifier is configured for the line
voltage in the market for which it is intended. For ex-
ample, those intended for Japan are 100 VAC; for North
and Central America, 120 VAC; for Europe and most of
Asia, 220–240 VAC.
OCCASIONAL CLIPPING
The “PWR” and “SIG” LEDs are lit,
and the “CLIP” LED flashes on
occasional peaks. This is normal.
CLIP PROT
PWR SIG
STEADY CLIPPING
The“PWR”,“SIG”,and“CLIP”LEDs
are lit continuously. The channel is
in hard clipping, and you should
reduce power immediately to avoid
speaker damage.
CLIP PROT
PWR SIG
The power cord has a plug for connecting to a standard
AC source. For 120-volt operation, the plug is a standard
15-amperegroundedNEMAfitting;itmeetssafetyagency
requirements for current consumption of less than 12
amperes during “normal” operation, but peak current
draw under heavy usage can be much higher.
THERMAL MUTING
PWR SIG
The “SIG” LED is flashing, and the
“PROT” LED is lit; this indicates
that the protection circuitry is mut-
ing the output. The condition will
reset itself when conditions allow.
CLIP PROT
KEY
Not Illuminated
Flashing
Full Brightness
Figure 5: LED displays further explained.
6
PROBLEM: Hum in the audio
Because of its grounded-collector output
TROUBLESHOOTING
•
transistor configuration, which maximizes
thermal efficiency, the signal ground on an
MXaamplifiercannotbelifted.Theamplifier’s
balancedinputsaremeanttorejecthum,but
if hum remains a problem, check the tight-
ness of the two mounting screws on the
standard input panel; if they are loose, the
panelitselfmightnotbewellgroundedtothe
chassis.Ifyouhaveanyproblemswiththese
screws, contact the QSC Customer Service
Department. In some cases, such as when
the audio signal cables are routed near
lighting dimmers that use triacs, you may
need to use input isolation transformers be-
cause of the extremely high noise field pro-
duced by the dimmer circuitry. See the para-
graphs on Open Input Architecture for fur-
ther information on input transformers.
PROBLEM: Channel will not come out of muting
•
If reducing the gain control to ∞ attenuation
does not release muting, the channel is
defective or overheated (see“Overheating,”
below).
•
If reducing the gain releases the muting,
raise the gain back up slowly while you
watch the “SIG” and “CLIP” indicators; the
problem may be an abnormal signal (with
excessive ultrasonic energy, for example)
that could otherwise damage your speak-
ers.
PROBLEM: No sound
•
Is the channel muted? (If the “PROT” indica-
tor is lit, the channel is muted; see below.)
In addition, be sure to check wiring to assure
that shields are properly terminated and no
ground loops have been created.
•
Is the “SIG” LED lit or flashing? (If so, the
speaker is open or blown, there is an open
circuit in the speaker wiring, or there is an
open circuit in the internal output wiring of
the amplifier.)
PROBLEM: Overheating
•
•
If the “SIG” indicator is dark, there is prob-
ably not enough signal, or even none at all.
Try turning up the front panel attenuators or
boosting the signal level at the input.
•
The thermal management system on an
MXa Series amplifier features either a two-
speed fan (MX 1000a, MX 1500a, and MX
2000a) or a variable-speed fan (MX 3000a)
that modulates the cooling air flow over the
heatsinks in response to the cooling needs.
If the air flow is blocked, however, or if the
amplifier is overdriven into very low imped-
ance loads, the amplifier could overheat
even though the fan is running at full speed.
Ifthe“SIG”indicatorshowslittleornoactivity
but the “CLIP” LED is lit or flashing, there is
probablyashortcircuitinthespeakerwiring.
It is also possible, but less likely, that the
channel’s output relay is defective and will
not open, thereby short-circuiting the chan-
nel output and producing the same symp-
toms.
•
•
At approximately 55°C, the fan runs at high
speed.
At approximately 80˚ C, the thermal limiter
on the MX 3000a will start to reduce gain, up
to 15 dB as needed, to reduce the amount of
heat produced.
PROBLEM: Channel goes into muting, with “PROT”
LED on
•
If the fan is running full speed, the channel
probably suffers from severe overheating.
Unless there is a blockage in the flow of
cooling air, the channel should return to
normalwithinaminuteorso(see“Overheat-
ing,” below).
•
Atapproximately85˚C,thechannel’soutput
relay will mute the output. The channel will
remain muted until the temperature drops to
asafelevel.Evenwhilethechannelismuted,
the “SIG” and “CLIP” indicators will function
normally. If the “CLIP” indicator is flashing or
continuously lit, reduce the gain to hasten
the cool-down and prevent repeated ther-
mal shutdowns.
•
If the fan is not running at full speed, or the
channel does not reset to normal after a
cool-down period, the muting is probably
because of a DC fault or other amplifier
failure, especially if the “SIG” or “CLIP” indi-
cators are lit even with the attenuator turned
all the way down.
7
SPECIFICATIONS
FTC Watts Per Channel 20Hz-20kHz, 0.1% THD EIA Watts Per Channel 1kHz, 1% THD
MODEL
8Ω Load
4Ω Load
8Ω Load
4Ω Load
2Ω Load*
MX 1000a
MX 1500a
MX 2000a
MX 3000a
250
350
450
800
350
500
650
1200
275
400
475
850
400
600
725
1300
500
750
1000
1600
*typical
Bridged Mono 20Hz-20kHz, 0.1% THD
Bridged Mono 1kHz, 1% THD
MODEL
16Ω Load
8Ω Load
4Ω Load*
MX 1000a
MX 1500a
MX 2000a
MX 3000a
500
700
900
1600
700
1000
1500
2000
3200
1000
1300
2400
*typical
MX 1000a
MX 1500a
MX 2000a
MX 3000a
DYNAMIC HEADROOM
8 ohms
2.0
2.3
2.0
2.5
2.0
2.5
1.9
2.9
4 ohms
DISTORTION
SMPTE-IM
Less than 0.05%
FREQUENCY RESPONSE
20 Hz to 20 kHz, ±0.15 dB
8 Hz to 100 kHz, +0, -3 dB
DAMPING FACTOR
NOISE (A-weighted)
VOLTAGE GAIN, dB
Greater than 200
100 dB below rated output (20 Hz to 20 kHz)
40 (32 dB)
1.1
50 (34 dB)
1.07
56 (35 dB)
1.05
80 (38 dB)
1.0
SENSITIVITY, V RMS
(for rated power, 8-ohms)
INPUT IMPEDANCE
CONTROLS
10K unbalanced
20K balanced
Front: AC Switch, Ch. 1 and Ch. 2 Attenuator Knobs
Rear: Parallel/Stereo/Bridge Switch
INDICATORS (per channel)
PWR:
SIG:
CLIP:
PROT:
Green LED
Yellow LED
Red LED
Red LED
8
MX 1000a
MX 1500a
MX 2000a
MX 3000a
CONNECTORS (each channel)
COOLING
Input:
Output:
Barrier strip and 1/4” RTS phone jack
“Touch-Proof” binding posts
MX 1000a, MX 1500a, MX 2000a: 2-speed fan with back-to-front air flow
MX 3000a: Continuously variable speed fan, with back-to-front air flow
AMPLIFIER PROTECTION
Output Averaging™ short-circuit protection, open circuit, ultrasonic, RF, thermal
muting (thermal limiting also on MX 3000a). Stable into reactive or mismatched
loads.
LOAD PROTECTION
Turn-on/turn-off muting, clip limiting (MX 3000a only), DC-fault load grounding
relay with internal fault fuses.
OUTPUT CIRCUIT TYPE
MX 1000a, MX 1500a, MX 2000a: Complementary linear stage with
2-step high-efficiency circuit
MX 3000a: Complementary linear stage 3-step high-efficiency circuit
POWER REQUIREMENTS
100, 120, 220-240 VAC, 50/60 Hz
POWER CONSUMPTION
Normal operation: 1/8 power @ 4Ω per channel
Maximum: full power @ 2Ω per channel
Divide current by 2 for 220-240 VAC operation
Normal Operation @ 120 VAC
Maximum @ 120 VAC
4A
22A
5.5A
29A
7.5A
38A
<12A
58A
DIMENSIONS
Faceplate Width
Chassis Depth
Standard 19" (48.3 cm) Rack Mounting
17.9” (45.5 cm) deep (to support rear ears)
Faceplate Height (2 rack spaces)
Faceplate Height (3 rack spaces)
3.5” (8.9 cm)
3.5” (8.9 cm)
5.25” (13.3 cm)
5.25” (13.3 cm)
WEIGHT
Shipping, Lbs
Net, Lbs
49 lbs/22.2 kg
42 lbs/19 kg
49 lbs/22.2 kg
42 lbs/19 kg
62 lbs/28 kg
54 lbs/24.5 kg
74 lbs/33.8 kg
69 lbs/31 kg
OPEN INPUT ARCHITECTURE™ LEVEL I
On the rear of an MXa or EX amplifier are an upper and
a lower input panel; both are easily removable for future
upgrades. ThisistheconceptofOpenInputArchitecture,
and the opening in which the panels mount is called the
“slot”. As installed at the factory, the lower is the MXa or
EX standard input panel and the upper one is a blank. A
ribbon cable connects the “slot” panels to the rest of the
amplifier. It carries input signals, speaker output monitor
signals, muting status, and clip activity; these are for
supporting future accessories and remote control sys-
tems. Although the physical dimensions of the MXa and
EX panels are the same, their internal cabling is different
and the MXa platform does not support all the EX
functions. The MXa Open Input Architecture slot thus is
designated as “Level I” and the EX as “Level II.”
The MX-1 Input Expander panel may be installed in the
upper panel position. It features XLR inputs and addi-
tional 1/4” RTS inputs. Installation instructions are in-
cluded with the expansion kit.
Other accessories include a stereo precision attenuator
(for the lower panel position) and a cinema crossover (for
the upper panel position). More are in development.
The standard input panel shipped with each MXa Series
amplifier has balanced 1/4” (6.3 mm) RTS phone jacks
and barrier strip inputs and the Parallel-Stereo-Bridge
switch. The panel’s circuit board has solder footprints for
passive roll-off circuit components, input isolation trans-
formers, and other special customizations.
9
INSTRUCTIONS FOR BRIDGED
OPERATION
PARALLEL, STEREO, OR BRIDGED
OPERATION
1. Set the switch to the “Bridge” position.
The Parallel-Stereo-Bridge switch is located on the input
panel, next to the input jack for channel 1).
2. Connect the signal to channel 1’s input only.
Do not connect anything to the input of
channel 2.
The most commonly used operating mode for a power
amplifier is “Stereo,” in which the two channels are
independent and separate all the way from input to
output. Set the switch in the center position for stereo
operation.
3. Turn up the gain on channel 2 all the way.
Use channel 1’s gain control to set the level.
Both channels’ “SIG” and “CLIP” indicators
should flash identically. (If you have used
other amplifiers, this step may be different.
But it is correct; in the bridged mode, chan-
nel 2 receives its feed from a sample of
channel 1’s output. The sample is calibrated
such that channel 2, at full gain, will produce
a voltage equal in magnitude but opposite in
polarity to channel 1’s.
“Parallel”tiesthetwochannelinputstogethersothatboth
will be driven by the same signal, without the need for
externaljumpersorwiring. Aftertheinputsbothchannels
operate independently; though they carry the same sig-
nal, their gain controls affect only their respective chan-
nels, and they must use separate speakers. Never par-
allel the speaker outputs!
The “Bridge” position uses both channels to provide
about three times the power to a single speaker load that
a single channel does. In this position the switch feeds
channel 2 with an inverted signal from channel 1. Thus,
when one channel “pushes,” the other “pulls,” providing
twice the voltage swing of a single channel.
4. Connect the single speaker load across the
red binding posts of the amplifier outputs as
shown in Figure 2-2. The positive speaker
wire goes to channel 1, and the negative to
channel 2.
BRIDGED-MONO MODE CAUTION:
TIP NEG RING POS
SLEEVE GND
The voltage across the outputterminals ofa bridgedMXa
amplifier may equal or exceed 100 volts rms and may be
as high as 170 volts (MX 3000a), 130 volts (MX 2000a), or
120 volts (MX 1500a). Use fully insulated CLASS ONE
wiring, andthe loadmustbe ratedforupto2400watts (@
8 ohms) for the MX 3000a, 1300 watts (@ 8 ohms) for the
MX 2000a, 1000 watts (@ 8 ohms) for the MX 1500a, and
700 watts (@ 8 ohms) for the MX 1000a.
STEREO
PARALLEL
BRIDGE
CH 1
Figure 6: Parallel-Stereo-Bridge switch shown in the
normal (Stereo) mode position.
VORSICHT BEIM ÜBERBRÜCKTEN
MONO-MODUS:
STEREO
Switch on Input Panel
(Left side of rear panel)
PARALLEL
BRIDGE
Zwischen den überbrückten Terminals eines MXa-
Verstärkers besteht eine Ausgangsspannung mit einem
quadratischen Mittelwert von mehr als 100 Volt und
vielleicht von bis zu 170 Volt (MX 3000a), 130 Volt (MX
2000a), oder 120 Volt (MX1500a). Zu verwenden ist voll
isolierte Verdrahtung der US-Klasse Eins, und die
angeschlossene Belastung muß für bis zu 2400 Watt (8
Ohm) beim MX 3000a, 1300 Watt (8 Ohm) beim MX 2000a,
1000 Watt (8 Ohm) beim MX 1500a, und 700 Watt (8 Ohm)
beim MX 1000a ausgelegt sein.
–
–
BRIDGED MONO
–
+
+
CHANNEL 2
CHANNEL 1
–
–
CLASS 2 WIRING
STEREO 4 OHM MIN/CH.
BRIDGED MONO 8 OHM MIN. CLASS 1 WIRING MUST BE USED
BRIDGED MONO OPERATION: PLACE BRIDGING SWITCH ON INPUT PANEL
TO BRIDGED POSITION. CONNECT INPUT SIGNAL TO CH 1 ONLY.
CONNECT SPKR (+) TO CH 1 (+) OUTPUT. CONNECT SPEAKER (–) TO
CH 2 (+) OUTPUT. SET CH 2 GAIN FULLY CLOCKWISE AND REGULATE
LEVEL WITH CH 1 GAIN CONTROL.
+
CONNECT ONE SPEAKER LOAD ONLY.
Figure 7: For Bridge mode, use CH 1 input only, and set
Input switch and connect load as shown.
10
AC CURRENT CONSUMPTION
VI. LONG-TERM OUTPUT
POWER
A major objective in the design of the MXa Series
amplifiers—even the highest-powered models—is to
permit their operation from readily available, standard
ACpowersources.TheMX3000acandeliver1600watts
per channel into 2-ohm loads—a total of 3200 watts—yet
its rated current draw under “normal conditions” is less
than 12 amperes at 120 volts AC, which is 1440 watts.
In a properly designed sound system, you can usually
obtain the desired sound level without using the full
outputpoweroftheamplifier;ifthe“CLIP”indicatorsflash
once in a while, that is perfectly normal.
Iftheamplifierisoperatedatextremelyhighpowerlevels,
it may overheat or may even damage the speakers. The
amount of stress on the amplifier depends largely on the
load and how hard the amplifier drives it. In general, the
lower the load impedance, the more stressful the load is.
How is this possible? First, “normal conditions” in power
amplifier rating means operation, using pink noise as a
source, at an average power level equal to one-eighth of
maximum power. This is recognized by most of the
world’s safety agencies as the loudest you can play
music through an amplifier and still keep the incidence of
clipping to a reasonable minimum. An amplifier’s peak
current draw at full output power into 2 ohms is several
times what the “normal” draw is, but its various protection
circuits will prevent this condition’s lasting more than a
minute or two.
8-Ohm Loads
The amplifier can operate at practically any power level
without risk of overheating. However, if it is pushed hard
enough to continually light the “CLIP” indicator, the
amplifier’s average output power can reach 250 to 800
watts (depending on the model), which is more than
many speakers can handle.
When you plan the AC power hookups for your amplifi-
ers, use Table 2 to predict the current requirements per
amplifier. You can use the one-eighth power figures to
predict the normal continuous current draw, then add a
safety margin to allow for occasional crescendos.
4-Ohm Loads
If the “CLIP” indicator flashes occasionally, the amplifier
is approaching its maximum long-term power capacity. If
it is lit about half the time, the amplifier channel will
probably go into thermal protection within a few minutes.
2-Ohm Loads
Except for an occasional flash, keep the “CLIP” indicator
dark to avoid overheating the amplifier channel.
Table 2: Current requirements, in amperes, at 120 VAC under various conditions (divide by 2 for 220–240 VAC operation):
Output
AC Current
AC Current
AC Current
AC Current
MODEL Load power
@ Full power @ 1/3 power @ 1/8 power @ Idle
MX 1000a
MX 1500a
MX 2000a
MX 3000a
8+8
4+4
2+2
275 x 2
400 x 2
500 x 2
10
15
22
5.5
7.5
10
3
4
5
1
1
1
8+8
4+4
2+2
400 x 2
600 x 2
750 x 2
14
21
29
7
11
13
4
5.5
6.5
1
1
1
8+8
4+4
2+2
475 x 2
725 x 2
1000 x 2
16
25
38
9.5
15
21
5
7.5
11
1
1
1
8+8
4+4
2+2
850 x 2
25
40
58
16
31
42
9.5
15
20
1
1
1
1300 x 2
1600 x 2
11
HEAT EMISSIONS
Essentially, a power amplifier draws electrical energy
from the AC mains, converts it to DC, and then converts
itagainintoananalogoftheinputsignaltosendouttothe
loudspeakers. Any AC power that enters the amplifier
through the power cord and does not exit through the
speaker outputs turns into heat, which the amplifier must
rid itself of by exhausting it to the outside. In indoor use
this may present a sizeable challenge to a building’s air
conditioning system. Use Table 3 to predict the heat that
will be emitted by your amplifier.
Table 3: Heat emissions of MXa amplifiers under various conditions:
Load 1/3 Power, both channels 1/8 Power, both channels Idle, both channels
MODEL
MX 1000a
BTU/hr
1035
kcal/hr
BTU/hr
580
kcal/hr
150
BTU/hr
kcal/hr
8Ω
4Ω
2Ω
265
365
545
75
75
75
20
20
20
1430
2140
270
305
915
1035
MX 1500a
MX 2000a
MX 3000a
8Ω
4Ω
2Ω
1165
1875
2770
295
475
700
770
1010
1415
195
255
360
110
110
110
28
28
28
8Ω
4Ω
2Ω
1850
3100
4730
470
785
1080
1755
2760
275
445
700
145
145
145
40
40
40
1195
8Ω
4Ω
2Ω
2980
7100
755
1795
2600
2015
3600
5040
510
910
200
200
200
50
50
50
10280
1275
PROTECTION CIRCUITS
The design goal in high-efficiency, lighter-weight ampli-
fierssuchastheMXaSeriesistocontrolmorepowerwith
fewer or smaller load-bearing components, e.g., resis-
tors, transistors, transformers, etc. However, the higher
power flow through these components makes effective,
responsive protection circuitry absolutely vital. To this
end,thedesignoftheMXaseriestakesacomprehensive
approach to protection.
ing the speakers when the amplifier is turned on or off.
The turn-on delay is approximately three seconds to
allow the power supplies and circuitry to stabilize. Turn-
off muting occurs almost immediately after power is shut
off. Muting occurs whether power is turned on and off
using the front panel power switch or externally at the AC
source.
An NTC (negative temperature coefficient) thermistor in
series with the power switch and transformer primary
limits inrush current. The thermistor initially has a high
resistance, which then diminishes rapidly as it warms, to
avoid power loss. Typically, the inrush current of an MXa
Series amplifier thus is equal to that of another amplifier
of about 1/3 to 1/2 its power rating.
As in all QSC amplifiers, the inputs are resistively buff-
ered for overload and RF protection. Chassis bypass
capacitors at inputs and outputs further improve RF
rejection.
MXa amplifiers use the proven Output Averaging™ short
circuit protection system. This circuit permits full output
current even into resistive or reactive 2-ohm loads, but
reduces the current safely by about 75% if the output is
shorted.
When the DC fault protection circuitry senses a DC
voltage on the amplifier output, it activates a relay which
shorts the output and load to ground. If the DC is due to
a fault in the amplifier channel’s output circuitry, it will
probably produce enough current flow to blow the fault
fuseinserieswiththeoutput.Thiswilldisablethechannel
Turn-on/turn-off muting keeps transients—both from the
amplifieritselfandfromupstreamequipment—fromreach-
12
output until it can be repaired, at which time the fuse
should be replaced also.
VIII. TECHNICAL ASSISTANCE
& SERVICE
Temperature sensors on the channel heatsinks and the
power transformers are part of the thermal management
circuitry. On the MX 1000a, MX 1500a, and MX 2000a,
the temperature sensors govern whether the dual-speed
fan should run at low or high speed. Below 55˚ C, the fan
runs at low speed; above, it runs at high speed. At or
above 85˚ C, the channel mutes to go into thermal
protection.
Servicing your unit requires a trained technician capable
of performing the type of service you need. There are no
user serviceable components inside your unit and the
danger of electric shock exists. Additionally, some of the
components in your unit has QSC specific parts that
require QSC replacements. Comprehensive service
manuals for some models are available at QSC.
On the MX 3000a, the thermal management circuitry
controls the variable-speed fan according to how much
cooling air flow is required. At and above 80˚ C, the
thermal limiting circuit reduces the audio signal by up to
15 dB. At 85˚ C, the channel mutes to go into thermal
protection.
TECHNICAL ASSISTANCE
If you suspect that your [product] is defective, check your
system configuration and [product] settings to determine
the origin of the problem. In many cases, incorrect audio
interfacing, poor cabling, or other system level impair-
ments are the cause of problems in audio systems. For
technical assistance beyond the information given in this
manual, QSC Technical Services may be contacted.
VII. WARRANTY AND
DISCLAIMERS
FACTORY SERVICE
DISCLAIMER
Intheeventthatyour[product]doesneedfactoryservice,
you may reach QSC Technical Services for return in-
structions. A Return Authorization (RA) number must be
obtained from QSC Technical Services. QSC may not
account for products that are returned without a Return
Authorization number.
QSC Audio Products, Inc. is not liable for any damage to
speakers, amplifiers, or any other equipment that is
caused by negligence or improper installation and/or use
of the SPL-1.
PRODUCT WARRANTY
QSC Audio Products, Inc. guarantees the SPL-1 to be
free from defective material and/or workmanship for a
period of three years from date of sale, and will replace
defective parts and repair malfunctioning products under
this warranty when the defect occurs under normal
installation and use—provided the unit is returned to our
factory via prepaid transportation with proof of purchase
(sales receipt). This warranty provides that examination
of the returned product must disclose, in our judgment, a
manufacturing defect. This warranty does not extend to
any product which has been subject to misuse, neglect,
accident, improper installation, or where the date code
has been removed or defaced.
Product Return Guidelines
1. Pack the product well for protection during ship-
ment. QSC will provide the factory packaging free
of charge upon request.
2. Include a copy of the sales receipt, your name,
return address, phone number, and defect de-
scription with your return correspondence.
3. Call QSC Technical Services for a Return Autho-
rization number.
4. Mark the Return Authorization number on the
outside of the packaging.
5. Ship the product prepaid to QSC Audio Products.
We recommend United Parcel Service (UPS).
QSC TECHNICAL SERVICES
1675 MacArthur Blvd
Costa Mesa, CA 92626
Telephone: (800) 772-2834
(714) 957-7150
(714) 754-6175
Fax: (714) 754-6173
Bulletin Board: (714) 668-7567
13
File Library
QSControl Hardware Support
QUALIFIED SERVICE CENTERS
QSC maintains a service center network for your conve-
nience. If you choose to return your product to a local
service center, you may call QSC Technical Services for
a referral. Accessories, input modules and other periph-
eral QSC products must be returned to the factory for
service.
QSControl Software Support
EX, MXa, VS, USA, and Series One
Slot Accessories
General Notes
File Types
Graphics
Mechanical drawings
Specifications
Application notes
INTERNATIONAL SERVICING
Field service notes
Service bulletins
For QSC products that are purchased outside of the
United States, service must be referred to the distributor
or dealer from where the product was purchased. There
are numerous service centers in many countries. The
service centers in your country may be located by your
dealer, distributor, or by contacting QSC Technical Ser-
vices.
Schematics
Pin-outs
Owners manual text segments
Environment files
Computer utilities and drivers
Service manual text segments
Computer configuration tips
Block diagrams
These are primarily text, graphics, utility, and program files.
IX. QSC ONLINE
Security Levels
New User
Full User
QSC User
Sysop
Cursory access, for review
Customer access
Full access
If you have a computer with a modem you can take
advantage of QSC’s convenient technical support bulle-
tin board system, QSC OnLine. Download software
updates, messages, or hardware application notes; up-
load questions, comments, and useful tips, and more.
This service is available free of charge, around the clock,
Supervisory access
User Privileges and Security
New User
Full User
QSC User
30 minutes per day
No uploads
No downloads
365 days a year (366 days in leap years).
Standard messages access
Bulletin access
As of March 18, 1994—
90 minutes per day
5 uploads per day
BBS Hours:
24 hours a day
BBS Telephone Number:
(714) 668-7567
5 downloads per day
Standard messages access
Bulletin access
General
Automatic system maintenance hours:
Unlimited time per day
10 uploads per day
1:00 a.m.–2:00 a.m. Pacific Time
(no log-ons during this hour)
10 downloads per day
Unlimited messages access
All menu and system access
System type:
Host location:
Open (no subscription fee)
QSC Customer Service Department
Costa Mesa, California
*Uploads and messages subject to verification and editing by the sysop.
Support Areas
Communications Settings
Bulletins
14400 bps (also supports 1200, 2400, and 9600 bps)
Advertisements
8 bits, no parity, 1 stop bit
Ordering and Support Information
Newsletter
Conferences
Mail Messages
General Forum
Parts & Accessory Ordering
Technical Commentary
QSControl Hardware Support
QSControl Software Support
EX, MXa, VS, USA, and Series One
Slot Accessories
General Notes
14
X. IMPORTANT ADDRESS AND
TELEPHONE INFORMATION
Factory address:
QSC Audio Products, Inc.
1675 MacArthur Boulevard
Costa Mesa, California 92626-1468
USA
Factory telephone numbers:
Main Number
(714) 754-6175
Sales Direct Line
Sales
(714) 957-7100
(800) 854-4079
(toll-free in U.S.A. only)
Sales & Marketing FAX
(714) 754-6174
(714) 957-7150
Customer Service
Customer Service
(800) 772-2834
(toll-free in U.S.A. only)
Customer Service FAX
QSC OnLine Technical
(714) 754-6173
(714) 668-7567
15
®
A
U
D
I
O
“QSC” is a registered trademark of QSC Audio Products, Inc.
1675 MacArthur Blvd. Costa Mesa, CA 92626
(714) 754-6175 FAX (714) 754-6174
|
Raritan Computer Network Card EMX2 111 User Guide
Remington Electric Shaver 400 User Guide
RIDGID Water Pump SP 330 User Guide
Rinnai Furnace ES38 User Guide
RocketFish Video Gaming Accessories RF GWII015 User Guide
Samsung DVD Player AK68 00435B User Guide
Samsung Home Theater System HT E350 User Guide
Samsung Stereo System MAX VB630 User Guide
Sanyo Vacuum Cleaner SC X1000P User Guide
Scientific Atlanta Modem DPC2100 User Guide