OWNER'S MANUAL
AND INSTALLATION GUIDE
Auto Reverse
AV-428
AV-428
DETACHABLE FRONT PANEL AM/FM/MPX RADIO
WITH AUTO-REVERSE CASSETTE PLAYER,
CD CHANGER CONTROLS AND QUARTZ CLOCK
Toll-Free Installation Assistance
The installation and wiring connections for this unit are so simple, we doubt you'll need our help, but, if you do, we're
here to help you. Just call our toll-free telephone assistance line at 1-800-645-4994 during the days and hours shown
(U.S.A. and Canada only).
TIME ZONE
EASTERN
DAY
PACIFIC
MOUNTAIN
CENTRAL
MON.-FRI.
SATURDAY
8:30AM - 7PM
9AM - 5PM
5:30AM - 4PM
6AM - 2PM
6:30AM - 5PM
7AM - 3PM
7:30AM - 6PM
8AM - 4PM
UNIVERSAL INSTALLATION USING MOUNTING SLEEVE
EXISTING DASH OPENING (FILE EDGES TO FIT IF NECESSARY-DO NOT OVERFILE)
NOTE: IF DASH IS SOLID, USE MOUNTING SLEEVE AS A TEMPLATE & CUT OPENING
NUT
PERFORATED STRAP
BEND TOP TABS
UPWARD
FASTEN THIS END TO
SCREW STUD ON
REAR OF CHASSIS
BEND BOTTOM TABS
DOWNWARD
SCREW
RADIO
SCREW STUD
REMOVAL
TOOLS
MOUNTING SLEEVE
FASTEN THIS END TO SECURE PART
OF DASHBOARD.
DRILL HOLE IF NECESSARY.
DETACHABLE
FRONT PANEL
ISO INSTALLATION
TYPICAL INSTALLATION
REMOVE THE PLASTIC FRAME FROM THE
FRONT OF THE CHASSIS BY CAREFULLY
UNSNAPPING IT.
MAX. SIZE
M5 x 8
Unsnap AT 2 PLACES
EACH ON TOP AND
BOTTOM
PLASTIC FRAME
MAX. SIZE
M5 x 8
FACTORY MOUNTING BRACKETS
3
RADIO WIRING
REFER TO PAGE 5 FOR SPEAKER WIRING
AUTOMATIC
ANTENNA
ANTENNA
BLUE
FUSEBLOCK
EXISTING
ANTENNA
CABLE
“RADIO” FUSE
+ 12V ACCESSORY
RED
1-AMP FUSE
SCREW
BLACK
CAR BATTERY
METAL PART OF DASH
(DRILL HOLE IF NECESSARY)
IMPORTANT
YELLOWWIREMUSTBECONNECTEDASSHOWN
OR RADIO WILL NOT OPERATE PROPERLY
YELLOW
FILTER/FUSE
BOX
(12-AMPFUSE)
POSITIVE (+) TERMINAL
12V BATTERY
4 PIN PLUGS
9 PIN PLUG
ANTENNA PLUG
(SEE PAGE 5 FOR SPEAKER WIRING)
ANTENNA SOCKET
RADIO
4
SPEAKER WIRING
REFER TO PAGE 4
FOR RADIO WIRING
WARNING!
!
!
THE AMPLIFIERS IN THIS RADIO ARE ONLY DESIGNED FOR USE WITH 4 SPEAKERS.
NEVER COMBINE (BRIDGE) OUTPUTS FOR USE WITH 2 SPEAKERS.
!
!
NEVER GROUND NEGATIVE SPEAKER LEADS TO CHASSIS GROUND.
FAILURE TO WIRE EXACTLY AS SHOWN BELOW MAY CAUSE ELECTRICAL DAMAGE TO THE RADIO.
NOTE:
RCA JACKS
LINE OUT
FOR USE WITH
OPTIONAL
CALL 1-800-645-4994 FOR RECOMMENDATIONS
OF MODEL CHANGERS THAT WILL WORK WITH
YOURRADIO.
RADIO
EXTERNAL
OPTIONAL CD CHANGER
DIN CABLE (SUPPLIED
WITH CD CHANGER).
AMPLIFIERS
RED = RIGHT
WHITE = LEFT
6
COMPACT
8-PIN DIN SOCKET FOR CONNECTION TO
OPTIONAL CD CHANGER
4-PIN PLUGS
9-PIN PLUGS
LEFT FRONT SPEAKER
SEEPAGE4
RIGHT FRONT SPEAKER
FORRADIOWIRING
GRAY w/BLACK STRIPE
LACK STRIPE
WHITE
GREEN
GREEN w/BLACK STRIPE
VIOLET w/BLACK STRIPE
HELP!
LEFT REAR SPEAKER
RIGHT REAR SPEAKER
1-800-645-4994
Monday - Friday
Saturday
8:30am - 7:00pm Eastern
9:00am - 5:00pm Eastern
5
OPERATING INSTRUCTIONS
27, 28
BEHIND PANEL
22
23
21
15
24
30
19
20
29
14
25
3
4
5
6
7
Auto Reverse
AV-428
11
12
34
35
26
2
18
1
13
31 36 37 38
16
8, 10
17
9
32 33
automatically return to the normal indication 5 seconds
after the last adjustment or when another function is
activated.
1
ON-OFFPOWERBUTTON
Press this button to turn the unit on and off when the
ignition switch is on. When the unit is off, the Liquid
Crystal Display (LCD) panel will normally display the
time-of-day. If the radio is off when the ignition switch is
turned off, the POWER button must be pressed to turn on
the radio after the ignition switch is turned on. If the
ignition switch is turned off while the radio is on, the radio
will display thetimeof day,andwillcomeonautomatically
when the ignition switch is again turned on.
4
BASS CONTROL
To adjust the bass level, first select the Bass mode by
pressing the PUSH SELECT button so the BAS
indication appears on the display panel. Within 5 seconds
3
control
of choo2sing the Bass mode, rotate the Volume Level
CCW or CW to adjust the bass response as
desired. The level will be shown on the display panel from
a minimum --10 to a maximum of 10 (00 indicates flat
response). The display will automatically return to the
normal indication 5 seconds after the last adjustment or
when another function is activated.
2
VOLUMELEVELCONTROL
To increase the volume level, rotate the PUSH SELECT-
VOL control clockwise (CW). The volume will increase
and the level will be shown on the display panel from a
minimum of 00 to a maximum of 100. To decrease the
volume level, rotate the PUSH SELECT control counter-
clockwise (CCW). The volume will decrease as shown
This control also includes the
NOTE: If the BAS or TRE functions are set while the
Equalizer function (EQ) is active, the Equalizer
function will automatically revert to the FLAT
setting.
on the display3panel.
balance and fader levels as described in
for adjustment of th4e bass, treble,
6, and
,
5,
Select button
5
TREBLECONTROL
To adjust the treble level, first select the Treble mode by
pressing the PUSH SELECT button so the TRB
indication appears on the display panel. Within 5 seconds
7
.
3
3
SELECTBUTTON(SEL)
This button is used to select the audio function (bass,
treble, balance, or fade) to be adjusted using the Volume
Level control 2. Pressing the Select button once will set
the unit for volume adjustment (VOL will appear on the
display panel). Pressing the button additional times will
select bass adjustment (BAS on display), treble (TRB),
balance (BAL), or fader (FAD). The display will
control
of choo2sing the Treble mode, roatate the Volume Level
CCW or CW to adjust the treble response as
desired. The level will be shown on the display panel from
a minimum of --10 to a maximum of 10 (00 indicates flat
response). The display will automatically return to the
normal indication 5 seconds after the last adjustment or
when another function is activated.
6
6
LEFT/RIGHTBALANCECONTROL
To adjust the left-right speaker balance, first select the
Balance mode by pressing the PUSH SELECT button
Tuning (
) button to tune downward to the next
available station. The radio will automatically seek the
next strongest station. If the Local mode (LOCAL) is
active, the radio will seek the next strongest local station
when either button is pressed.
3
so the BAL indication appears on the display panel.
Within 5 seconds of choosing the Balance mode, rotate
the Volume Level control
2
CCW to adjust the stereo
bn
MANUALSEEKTUNING
balance to the left channel speakers, or CW to adjust it
to the right channel speakers. The balance position will
be shown on the display panel from BAL 10L (full left) to
BAL 10R (full right). When the volume level between the
left and right speakers is equal, BAL L=R will be shown
on the display panel. The display will automatically return
tothenormalindication5secondsafterthelastadjustment
or when another function is activated.
This function is used to search rapidly upward or
downward for a desired station. By pressing either tune
button for more than 2 seconds, the radio will enter the
MANUAL seek mode as displayed momentarily on the
panel. When either button is pressed and held in this
mode, the radio will tune rapidly up or down and will stop
at the station of choice when the button is released. A
momentary press of either button in this mode will cause
the radio to tune upward or downward one digit at a time.
If tuning is not activated within 5 seconds of entering the
MANUAL mode, the radio will automatically revert to the
so default AUTO mode as indicated momentarily on the
panel.
7
FRONT/REARFADERCONTROL
To adjust the front-rear speaker balance, first select the
Fader mode by pressing the PUSH SELECT button
3
the FAD indication appears on the display panel. Within
5secondsofchoosingtheFadermode, rotatetheVolume
bo
LOCAL/DISTANTSELECTOR(LOC)
Level control
2
CW or CCW to adjust the front-rear
This feature is used to select the strength of the signals
at which the radio will stop during Automatic Up/Down
Tuning. Pressing the button will select the Local setting
(LOCAL will appear on the display panel for 5 seconds)
and tuning will select only strong (local) stations for
reception. Pressing the button again will select the
Distant setting (DX will appear on the display panel for 5
seconds) and the tuning will stop at a wider range of
signals, including weaker (more distant) stations.
speaker balance as desired. The fader position will be
shown on the display panel from FAD 10R (full rear) to
FAD 10F(fullfront). Whenthelevelbetweenthefrontand
rear speakers is equal, FAD F=R will be shown on the
display panel. The display will automatically return to the
normal indication 5 seconds after the last adjustment or
when another function is activated.
8
LOUDNESSCONTOUR(LOUD)
When listening to music at low volume levels, this feature
will boost the bass and treble ranges to compensate for
the characteristics of human hearing. Press and hold the
BAND/LOUD button to activate this feature and the
indication LOUD ON will appear on the display panel for
5 seconds. Press and hold the button again to deactivate
the feature, and LOUD OFF will appear on the display
panel for 5 seconds.
bp
FM MONO SELECTOR (MONO)
During FM radio operation, this button is used to select
mono or stereo reception of the broadcast signal. Under
normal reception conditions, the unit should be left in the
stereo mode as indicated by ST and the associated
signal strength indicator on the display panel when tuned
to an FM stereo signal. If the stereo signal is too noisy for
comfortable listening, press the MONO button to switch
to mono reception (the ST indication will disappear from
the display panel, and MONO will momentarily appear).
To return to stereo reception mode, press the button
again; STEREO will momentarily appear on the display
panel and the ST indication returns.
9AUDIOMUTESELECTOR(MUT)
Press this button momentarily to mute the volume from
the system (MUTE will appear flashing on the display
panel). Pressing this button again, adjusting the Volume
Level control 2, or pressing any other button, will return
to the volume level setting in use before the Mute function
was activated.
bq
PRE-SET SCAN (PS) AUTO-STORETUNING(AS)
Press this button momentarily to scan the stations pre-
set into the memories on the 3 FM bands or the AM band.
The unit will stop at each pre-set station for 5 seconds
before continuing to the next pre-set station (the pre-set
number on the display panel will flash during Pre-Set
Scan operation). Press the button again momentarily to
stop Pre-Set Scan operation and remain on the selected
frequency.
bl
AM/FMBANDSELECTOR(BAND)
Each time the BAND/LOUD button is pressed, the radio
band is changed. The indications F1, F2, F3 or AM will
appear in the display panel according to your selection.
bm
AUTOMATIC UP/DOWN TUNING (
To select a radio station in the automatic mode,
momentarily press the Up Tuning ( ) button to
advancetheunit tothenextavailablestation, ortheDown
/
)
Pressing and holding the button for longer than 2 seconds
will activate the Auto-Store Tuning feature which will
automatically scan and enter up to 6 stations into the 6
7
pre-set memories on the band in use. After entering the NOTE: It is a characteristic of LCD panels that, if
stations into memory, the unit will automatically stop at
each station for 5 seconds so each can be heard. If you
have already set the pre-set memories to your favorite
stations, activating the Auto-Store Tuning feature will
erase those stations and enter the new ones. This
feature is most useful when travelling in a new area
where you are not familiar with the local stations.
subjected to cold temperatures for an extended
period of time, they may take longer to illuminate
than under normal conditions. In addition,
the visibility of the numbers on the LCD may
slightly decrease. The LCD read-out will return
to normal when the temperature increases to
a normal range.
cl
CASSETTE DOOR
br
STATION PRE-SET MEMORIES
To set any of the 6 pre-set memories in each band, use
the following procedure:
Hold the cassette with the exposed tape edge to the right
and insert it fully into the cassette door until the cassette
is engaged and begins playing (TAPE will appear on the
display panel, together with three tape direction arrows).
When the cassette reaches the end on the side of the tape
being played, the unit will automatically change direction
of play as shown by reversal of the three tape direction
arrow indications on the display panel.
1. Turn the radio on and select the desired band.
2. Select the first station to be pre-set using the
Automatic Up/Down bm, or Manual Seek
bn
Tuning
Controls.
3. Press and hold the pre-set button to be set for
approximately 2 seconds. The pre-set number will
appear on the display panel indicating that the station
is now set into that pre-set memory position. The
station can now be recalled at any time by pressing
that button.
NOTE: Observe cassette operation cautions in Care
and Maintenance section of this manual.
cm&cnFAST-FORWARD/REWINDBUTTONS
) These buttons cause the tape to move rapidly
(
/
4. Repeat the above procedure for the remaining 5
pre-sets on that band and for the other 3 bands
in the direction indicated by the arrows. For example, if
the
to right ( >>> on the display panel), the tape will fast-
forward. If the button is pressed while the tape is
moving from right to left ( <<< on the display panel), the
tape will rewind. To stop fast tape movement, lightly push
the opposite button. If the tape is allowed to fast-forward
or rewind all the way to the end, the tape will reverse and
button is pushed when the tape is moving from left
bson the unit.
EQUALIZER (EQ) BUTTON
The EQ button applies preset sound effects to the unit’s
audio output signal.The EQ button, when pressed, will
activateoneofthefollowingoperatingmodes(CLASSICS,
POP M, ROCK M, DSP OFF or FLAT). If the Equalizer
function is active, as momentarily displayed on the panel,
and the bass and/or treble level is set, the Equalizer
function revertstothetheFLATsetting.Ontheotherhand,
if the Equalizer function is activated, the bass/treble
setting(s) are ignored. Conversely, when the Equalizer
function is not active, the unit returns to the user set bass
and treble levels.
automatically resume play.
co
PROGRAMSELECTOR
To manually reverse tape direction and play the other side
(program) of the cassette, lightly push both the Fast-
Forward and Rewind buttons (
time. The change of direction will be shown by the arrows
on the display panel.
and
) at the same
bt
STATION SCAN (SCN) BUTTON
When this button is pressed during radio operation, each
station in the current band will be scanned in the upward
direction; each displayed station will flash for 5 seconds
before moving on to the next station. If the local mode is
active, only the stronger, nearby stations in the current
band will be scanned. When the desired station appears,
press the SCN button again to remain on that frequency.
cp
EJECT BUTTON (
)
Tape playback is stopped and the cassette is ejected by
pressing this button. Radio operation will automatically
resume when the cassette is ejected.
NOTE: Never leave a cassette engaged in the player
when not in use. Doing so can cause damage
to the cassette and/or mechanism of the unit.
Always press the eject button and remove
the cassette before removing the detachable
front panel.
bu
LIQUIDCRYSTALDISPLAYPANEL
The Liquid Crystal Display (LCD) panel displays the
frequency, time and activated functions, including a
combination audio level/disc indicator in the form of dual
disc icons (
) with circular bar graphs depicting the
cq
MODESELECTOR(MODE)
During radio or tape play, press this button to select
operation of the optional CD changer as shown by CDC,
the disc number and the track number on the display
panel. Refer to the CD Changer Controls section for
specific operating instructions.
strength of the audio signal. In addition, the display also
contains a receive signal indicator which depicts the
relative strength of the incoming broadcast frequency.
8
If the button is pressed when no CD changer is connected
to the unit, no CDC indications will appear on the display
panel. The unit will then return to radio operation. To
return to the tape operation (if a tape is loaded in the unit),
press the button again. During tape play, press this
button to change to radio operation without ejecting the
cu
FRONTPANELRELEASEBUTTON
This button is used to release the mechanism that holds the
front panel to the chassis. To detach the front panel, press
thebuttonsothattheleftsideofthepanelisreleased. Grasp
the released side and pull it off of the chassis. To re-attach
the panel, position the right side of the panel in place first
and then press the left side of the panel until the mechanism
locks it into place.
tcarpe.
TIME/FREQUENCYSELECTOR(T/F)
Pressing the Time/Frequency (T/F) button will display
the time of day for 5 seconds, after which the display will
automatically return to the radio, tape or CD changer
display, depending on which one was currently active.
To set the correct time of day, refer to the procedure for
Setting the Clock.
dl
DIMMER BUTTON (DIM)
This button provides control of the panel display brightness;
when pressed once, the display will dim to half its normal
intensity. When pressed again, the display will return to full
brightness intensity.
NOTESONUSEOFFRONTPANEL
csTHEFT-DETERRENTLED
Located on the chassis behind the front panel, a light-
emittingdiode(LED)willflashwhenthepanelisremoved.
The flashing light serves as a visual warning to the
would-be thief that the unit has been disabled by removal
1. Make sure the front panel is right-side-up when
attaching it to the chassis as it cannot be attached
when up-side down.
ocftthe front panel.
RESET BUTTON
2. Donotpressveryhardonthefrontpanelwhenattaching
it to the chassis. No more than light to moderate
pressure should be needed.
A RESET button is located on the front of the chassis
(front panel must be removed to access the button). The
re-set circuitry is provided to protect the microprocessor
circuitry and should only be activated under the following
circumstances as it will erase the time and pre-set
memories.
3. When attaching the front panel, make sure the right
side is correctly engaged before pressing the left side
to lock it into position.
4. When taking the front panel with you, please use the
supplied carrying case to protect the panel from dirt
and damage. Make sure there is no dust or dirt on the
electrical terminals on the back of the panel as this
could cause intermittent operation or other
1. Upon initial installation after all wiring is completed.
2. If there is a malfunction of any of the switches on
the unit, pressing the RESET button may clear the
system and return to normal operation.
malfunctions.
SETTING THE CLOCK
1. Switch the vehicle ignition and radio on.
2. Momentarily press the Time/Frequency (T/F) Select button
cr
so that the time is shown on the display panel.
3. Press and hold the Time/Frequency button until the time display begins flashing. While the display is still flashing,
press the Up Tuning ( ) button to adjust the hours and then the Down Tuning (
minutes to the correct time.
) button to adjust the
4. Five seconds after the last hour or minute adjustment is made, the time will be set in the unit and the display
will return to the normal indication.
9
HANDLINGCOMPACTDISCS(OPTIONALCDCHANGER)
CARE AND MAINTENANCE
Dirt, dust, scratches, and warpage can cause skips in the
playback and deterioration of sound quality. Please follow
these guidelines to take care of your compact discs:
The radio section of your new sound system does not
require any maintenance. We recommend that you keep
this manual for reference on the many features found in
this unit as well as how to set the clock.
The optional compact disc changer section also
requires no routine maintenance, but proper under-
standing of its use and handling will help you obtain
maximum enjoyment of its capabilities.
!Use only compact discs with the mark
.
!Fingerprints, dust, and dirt should be carefully wiped off
the disc’s playing surface (shiny side) with a soft cloth.
Wipe in a straight motion from the inside to the outside
of the disc.
CASSETTECARE
As with any cassette player, the cassette section of this
sound system does require a minimum of maintenance
to keep it in good working condition. The following simple
care and maintenance suggestions should be followed to
prevent malfunctions of the cassette system.
!Never use chemicals such as record sprays,
household cleaners or thinner to clean compact discs.
Such chemicals can irreparably damage the disc’s
surface.
!Discs should be kept in their storage cases when not in
use.
1. Purchase a cassette cleaning kit from your local
retail store. Use it! At least every 20 to 30 hours !Do not expose discs to direct sunlight, high temperatures
of operation you must clean the cassette mecha-
nism. A dirty cassette player will have a poor
sound.
or high humidity for extended periods.
!Do not stick paper, tape, or labels on the disc surfaces
nor write on them with any type of marker.
2. Do not use cassettes that exceed 45 minutes of
play on each side.
3. Do not insert a cassette that appears to be broken,
twisted or dirty or with loose or torn labels on it.
4. Always keep your cassettes away from direct sun
light or exposure to subfreezing conditions. If a
cassette is cold, allow it to warm up before use.
5. Do not keep a cassette in the player when not in use.
6. Before inserting a cassette in the player, check
that the tape is tightly wound on the reels. Take
up any excess slack using a pencil to turn the
drive hub in the cassette.
10
SPECIFICATIONS
Size:
7” W
x
2” H
x
6” D
178 mm x 50 mm x 150 mm
Operating Voltage:
Output Power:
12 volts DC, negative ground
160 watts maximum (40 watts x 4 channels)
Output Wiring:
Floating-ground type designed for 4 speaker use.
The amplifiers in this unit are NOT designed for use with 2 speakers.
RCA pre-amp level outputs.
Output Impedance:
Pre-Amp Output:
Tuning Range:
Compatible with 4 - 8 ohm speakers
500 mv.
AM: 530 - 1,710 KHz. (10 KHz. step)
FM: 87.5 - 107.9 MHz. (200 KHz. step)
Sensitivity:
AM: >45 dB.
FM: >15 dB at a S/N of 30 dB
FM Stereo Separation:
25 dB at 1kHz
Tape Frequency Response: 50-10,000 Hz.
Tape S/N Ratio:
Wow & Flutter:
50 dB
0.15% WRMS
*Specifications are subject to change without notice.
11
THISPAGELEFTBLANKINTENTIONALLY
12
CD CHANGER CONTROLS
dq
FOWARD/REVERSESEARCH(CUE/REVIEW)
High-speed audible search to any forward or reverse
section of the disc can be made with this feature. Press
Built into this radio are controls to operate an optional CD
changer. Please check with your Rampage/Audiovox car
stereo specialist for recommendations of the models
that will work with this radio.
and hold the forward (cue) button (
rapidly in the forward direction, or press and hold the
reverse (review) button ( ) to advance rapidly in the
reverse (backward) direction. In either case, the center of
the disc icon will rotate faster when search is active.
) to advance
Once the changer is installed and properly connected, it
may be necessary to press the RESET button behind the
radio front panel to initialize the complete installation.
Adjustment of the audio functions (volume, tone, balance,
and fader) for the CD changer operate in the same
manner as they do for radio play. The following controls
will operate the CD changer when it is installed and
connected to this radio. Refer to the owner’s manual
included with the CD changer for instructions on the
installation and correct loading and use of the CD
magazine.
dr
TRACKSCANSELECTOR(SCN)
When the SCN button is momentarily pressed, the SCN
indication will appear on the display panel, and the first
10 seconds of each track on the disc will be played in
order. When a desired track is reached, press the SCN
button again and play of the selected track will continue
(SCN will disappear from the display panel). The Track
Scan mode will also be canceled by activating any other
disc function (Track Select, Repeat or Random).
dm
CDCHANGERPAUSE/PLAYSELECTOR(PAU)
During radio, or tape play, press the MODE button to
select operation of the CD changer as shown by CDC on
the display. Disc play will begin, the disc and track
number will be shown on the display panel, and the
When the SCN button is pressed and held for more than
2 seconds, the disc scan mode is activated; DSN will
appear on the display and the first 10 seconds of the first
track on each disc will be played in disc order. This mode
is canceled in the same manner as before.
center of the disc icon (
) will become animated. If
a new magazine has been loaded into the changer, play
will begin from the first track of the first disc in the
magazine. If a magazine was already in the changer, play
will resume from the track on the disc previously in play.
During CD changer play, pressing the PAU button once
will stop changer play; PAUSE will appear on the display
and the center of the disc icon will remain stationary. To
resume disc play, press the PAU button again and disc
play will resume from the point at which it was interrupted.
ds
TRACKREPEATPLAYSELECTOR(RPT)
When the RPT button is momentarily pressed, the RPT
indication will appear on the display panel and play of the
current track will be continually repeated until the Track
Repeat mode is canceled by pressing the RPT button
again or by activating the Track Select, Random Play or
Scan functions.
When the RPT button is pressed and held for more than
2 seconds, the disc repeat mode is activated; DRT will
appear on the display and the play of the current disc will
be continuously repeated. This mode is canceled in the
same manner as before.
dn
&
do
DISC SELECT (DN & UP)
These buttons are used to select the desired disc for play.
To advance to a higher number disc, press the UP button
do
dn. To return to a lower number disc, press the DN button
. The number of the disc in play will be shown on the
dtSHUFFLEPLAYSELECTOR(SHF)
When the SHF button is momentarily pressed, the SHF
indication will appear on the display panel and the tracks
display panel.
Track Select buttons
on the disc will be playeddpin a random, shuffled order. The
will also select tracks in the
dp
TRACK SELECT (
This button is used to quickly select the beginning of a
particulartrack.WitheachmomentarypressoftheForward
/
)
shuffled order instead of the normal progression. The
Track Shuffle mode can be canceled by pressing the SHF
buttonagainorbyactivatingtheTrackSelect,RepeatPlay
or Scan functions.
When the SHF button is pressed and held for more than
2 seconds, the disc shuffle mode is activated; DSF will
appear on the display and the play of the discs in the
magazine will be played in a random shuffled order. This
mode is canceled in the same manner as before.
Track Select button (
will be selected as shown on the display panel. Similarly,
with each momentary press of the Backward Track Select
), the next higher track number
button(
), thenextlowertracknumber will beselected.
10
CD CHANGER ERROR CODES
If a problem should develop while operating the CD changer, the error code “Err” may appear on the display
panel. This can indicate a number of problems with the unit, including a mechanical error or an error in the
microprocessorcontrolofthechanger. Iftheerrorcodeshouldappear,tryejectingandre-loadingthemagazine
intothechanger. Whilethemagazineisoutofthechanger, makesurethediscsareclean, undamaged, and
loadedcorrectly(seeOwner’sManualoftheCDchanger). YoumayalsotryactivatingtheRESETbutton
on the unit, but this will also erase the time and pre-set memories.
ct
Ifthesuggestedmeasuresdonotsolvetheproblem,contactanapprovedwarrantystationnearyouforfurther
assistance.
14
12 MONTH LIMITED WARRANTY
AUDIOVOXCORPORATION(theCompany)warrantstotheoriginalretailpurchaserofthisproductthat
shouldthisproductoranypartthereof,undernormaluseandconditions,beprovendefectiveinmaterial
or workmanship within 12 months from the date of original purchase, such defect(s) will be repaired
orreplacedwithneworreconditionedproduct(attheCompany'soption)withoutchargeforpartsand
repairlabor.
To obtain repair or replacement within the terms of this Warranty, the product is to be delivered with
proofofwarrantycoverage(e.g. dated billofsale), specificationofdefect(s), transportationprepaid,
to the warranty center at the address shown below.
ThisWarrantydoesnotextendtotheeliminationofcarstaticormotornoise, tocorrectionofantenna
problems, to costs incurred for installation, removal, or reinstallation of the product, or damage to
tapes, compact discs, speakers, accessories, or vehicle electrical systems.
This Warranty does not apply to any product or part thereof which, in the opinion of the Company,
has suffered or been damaged through alteration, improper installation, mishandling, misuse,
neglect, accident, or by removal or defacement of the factory serial number/bar code label(s). THE
EXTENT OF THE COMPANY'S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE
REPAIRORREPLACEMENTPROVIDEDABOVEAND,INNOEVENT,SHALLTHECOMPANY'S
LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT.
This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED WARRANTIES,
INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, SHALL BE LIMITED TO THE
DURATIONOFTHISWRITTENWARRANTY. ANYACTIONFORBREACHOFANYWARRANTY
HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY MUST BE
BROUGHT WITHIN A PERIOD OF 30 MONTHS FROM DATE OF ORIGINAL PURCHASE. IN NO
CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL
DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED,
WHATSOEVER. No person or representative is authorized to assume for the Company any liability
other than expressed herein in connection with the sale of this product.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or
limitationofincidentalorconsequentialdamagesotheabovelimitationsorexclusionsmaynotapply
to you. This Warranty gives you specific legal rights and you may also have other rights which vary
from state to state.
U.S.A. : AUDIOVOX CORPORATION, 150 MARCUS BLVD., HAUPPAUGE, NEW YORK 11788 ! 1-800-645-4994
CANADA: CALL 1-800-645-4994 FOR LOCATION OF WARRANTY STATION SERVING YOUR AREA
128-4270E
15
© 2003 Audiovox Electronics Corp., Hauppauge, NY 11788
Printed in China
16
128-6634
|